 |
TOP |
> |
News Release |
 | NewsRelease |  | |
|
|
High-speed Graphics Transmission Compatible Cable Connector"FI-RE-HLS-M Series" 
|
2010/02/24
|
|
| |
::Features
- Space savings and improved operability with the top-side un-lock button.
Structure enables mating where there is no room to operate side buttons. - Mechanical lock to prevent incomplete-insertion and un-mating.
- Mates with standard FI-R Series receptacle.
- 100 ohm impedance matching with ground secured through metal cover shell structure.
- Connection with cable and contact (sold separately) by crimp method, compatible with inexpensive discrete wire.
Details |
 X |
|
|
|
|
|
High Reliability "MX39 Series" Connector For Automotive USB 2.0 Applications
|
2010/02/10
|
|
| |
::Features
- Connector and cable designed for automotive applications.
- Transmission performance meets PC level USB 2.0 standard.
- Noise removed due to double metal shell shielding structure for EMI control.
- 1 row, 4 position type with 2.2mm side pitch.
- Angle and straight board connector versions. Angle type with keys to prevent mis-mating is also available.
- Mechanical lock and twist-resistant structure for mated connector.
- In addition to board-to-cable type, cable-to-cable type is available for cable relay (allows for easier wiring during car assembly).
- Harness assembly done at JAE to ensure total reliability and transmission performance.
Details |
| X |
|
|
|
|
|
MXM3.0 Compatible Notebook PC Internal Graphics Board Connector "MM70 Series"Connector
|
2010/01/15
|
|
| |
::Features
- MXM3.0 standard (PCI-Express2.0 (x 16 lane), VGA, Dual LVDS, Displayport (supports (4 ports).
- Graphics board can be easily inserted at an angle..
- Precision positioning stopper prevents contact failure.
- Mating area is 0.5mm pitch, with two-layer upper and lower structure.
- Available in 6.7mm or 4.5 mm height, with 12.2 mm depth and 89.9 mm width.
Details |
| X |
|
|
|
|
|
"JN1/JN2 Series"Connector for Machinery and Industrial Equipment
|
2009/12/15
|
|
| |
::Features
- Easy and sure mating with push-twist type (Note 1) one-touch lock mechanism.
- Dust-proof and waterproof conforming to IP67.
- Superb environment-proof performance such as vibration and oil resistance.
- Straight and angled types. Can be set in four directions by rotating the plug in 90 degree increments.
- Compatible with conduit (Note 2) attachment.
- JN1 is an all plastic lightweight connector, JN2 is reinforced with metal material in part of the outer shell.
- Plug contacts can be selected from crimp or solder termination types.
* Note 1: One-touch lock mechanism enables mating by pushing in, and removal by twisting.
* Note 2: Flexible tube that can be added to protect the wires.
Details |
| X |
|
|
|
|
|
Lowest Height, Tray type, SIM Card Connector"SF8 Series"
|
2009/11/24
|
|
| |
::Features
- Tray type connector for GSM 11.11 standard plug-in SIM card
- Low profile structure: 1.55mm height, 16.65mm width, 19.30mm depth (26.2mm when tray is inserted)
- Available in standard A type and reverse B type, to accommodate different mounting needs.
- Connecter main body is provided in embossed tape (compatible with automated mounting and second reflow), card tray provided in trays (tray is attached to connector main body after main body is mounted to board)
- 4 grounding hold-downs ensure EMI/ESD control, and add strength to help prevent intermittence caused by dropping
- Retention lock on tray provides click feeling when mated, easy tray positioning during card insertion/removal, and keeps tray attached to the main connector body.
Details |
| X |
|
|
|
|
|
Compact, microSDTM Card Connector"ST1 Shrink Type"
|
2009/10/20
|
|
| |
::Features
- Push-slide structure connector for the microSDTM card standardized by the SDA.
- Balanced EMI control through 4 hold-down grounding points.
- Slim design with 1.4mm height, 15.5mm depth, 11.9mm width. 40% reduced volume and 20% reduced mounting area, compared to our previous product.
- Supplied in embossed tape for automatic mounting.
- Compatible with second reflow due to reduced weight (after surface solder reflow, back surface reflow also possible).
- Available with and without card insertion detection structure (D-SW), normally open.Part number: ST1-F (with insertion detection structure), ST1-G (without insertion detection structure).
- Locking structure prevents falling off of cover when dropped.
Details |
| X |
|
|
|
|
|
Notebook PC External Graphic Box Connector DL1 series
|
2009/10/02
|
|
| |
::Features
- Can be connected with high-end graphic boards, compatible with PCI Express 2.0 (x 8 lanes).
- Has terminals supporting USB 2.0 for convenient use with USB.
- Mating portion with 0.7mm pitch, 2-row structure.
- Compatible with hot pluging.
- Easy insertion and removal due to mechanical lock retention structure.
- No need to consider mating direction since the same connector is on both ends of cable.
- Available cables: 0.5m, 1m and 2m.
Details |
| X |
|
|
|
|
|
Lowest Height Ultra-thin FF07 Series FPC Connector
|
2009/08/20
|
|
| |
::Features
- 0.7mm height, the lowest FPC connector height in the industry.
3.85 mm depth, 0.3 mm pitch, ultra-thin and space saving design. - Easy lock for FPC connection with actuator on opposite side of insertion slot.
- Actuator set in "open" position at delivery enables insertion and locking in one-action to reduce customer man-hours.
- FPC upper connection structure is strong against FPC pulling in upward direction.
- Compatible with 0.12 mm ±0.02 mm, ultra-thin FPC
- ZIF (Zero Insertion Force) structure which requires no force for insertion/removal.
- Slanted insertion is prevented by touching the FPC side tabs to the connector during insertion.
- Bottom of the connector is covered with resin to prevent short-circuiting with the traces on board. This enables freer pattern tracing at connector bottom surface.
- Pb free and halogen free, environmentally friendly connector.
Details |
| X |
|
|
|
|
|
High-Speed Transmission Connector
With the Industry's Highest Pin Count FI-VHP
|
2009/07/15
|
|
| |
::Features
- FI-VHP available with 50 pos. and 40 pos., the industry's highest pin counts for a connector compatible with high-speed differential transmission such as LVDS and Display Port.
- FI-VHP is reinforced with a wall positioned in the center of the connector. The wall prevents bending of the receptacle insulator and damage to the contact caused by twisting and pulling of the plug.
- FI-VHP has secure shielding with a metal shell. EMI characteristics and board retention solder strength is improved by the multiple hold-downs (terminals for grounding).
- FI-VHP has a mechanical lock that effectively prevents disconnection caused by vibration and shock.
Cable side plug of FI-VHP has a guide on both mating sides to improve insertion performance. - FI-VHP plug side available only in solder type. Can be assembled with fine coaxial wire or discrete wire.
Details |
| X |
|
|
|
|
|
Space Saving
microSDTM and GSM 11.11 Plug in SIM Card Combo Connector ST7
|
2009/06/09
|
|
| |
::Features
(General)
(microSDTM side)- Easy to use push-push structure
- 1mm push stroke and 3.3mm card eject length for easy insertion/removal of card
- Card half-lock structure
- Design prevents the card from popping out
Details |
| X |
|
|
|
|
|
Compact, Low Pin Count Automotive Connector "MX34 Single Type"
|
2009/05/20
|
|
| |
::Features
- 2.2mm contact pitch, compact one-row board mounting type for board-to-cable, available in straight and angle types.
- Reduces customer man-hours with improved board attachment workability due to hook pins placed on both sides of pin connector, and no screw fixing required.
- Compatible with wire of thinner cross-section area than existing product, and made lighter to meet to customers application requirements.
- Socket contact is a box type which is strong against external force.
- Double spring structured contact area, resistant to twisting and prevents deformation of spring.
- Easy harness assembly with preset-type retainer.
- Contact incomplete-insertion detection mechanism.
- Mechanical lock method with assuring click when mated, and a bridge to protect lock lever.
Details |
| X |
|
|
|
|
|
Smaller than Previous Docking Connector
Compatible with PCI Express "WD2 series"
|
2009/04/06
|
|
| |
::Features
Pitch direction length decreased to two-thirds by reduced pin count structureDepth is also minimized and will contribute to saving mounting space for customersDesigned for high-speed serial transmission such as PCI Express and Display PortGround bar on receptacle side for ESD (Electrostatic Discharge) countermeasureAvailable in several mating heights and angle variationsMating guide length in pitch direction ± 1.3mm, cross direction ± 1.2mm 4 pos. (2 pair) for power in mating guide area with current capacity of 10A per pair, 20A in total144 pos. two row hot plug (hot plug not available for 100 pos.)
Details |
| X |
|
|
|
|
|
Ultra-Thin Coaxial Connector"FI-JK Series" Through 3.0mm Diameter Hings
|
2009/03/26
|
|
| |
::Features
- Industry leading compact plug side, can pass through 3.0mm dia. Hinge after harness assembly.
(When using 40 pos., 44AWG) - Noise-resistance characteristic is enhanced by Au plated ground contacts on the plug and receptacle,
not only on the sides, but also in the center of the connector. - Small size achieved: 1.34mm height, 3.7mm depth and 17.4mm width (40 pos.)
- Mis-mating prevention structure.
- Applicable wire: 42, 44, and 46 AWG fine-coaxial wire
- Receptacle is available in embossed reel compatible with automated mounting
- Solder migration prevention structure with Ni barrier on receptacle
Details |
| X |
|
|
|
|
